On the design of concentrator photovoltaic modules
- Authors: Schultz, Ross Dane
- Date: 2012
- Subjects: Photovoltaic cells -- Design and construction , Photovoltaic cells
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:10546 , http://hdl.handle.net/10948/d1015766 , Photovoltaic cells -- Design and construction , Photovoltaic cells
- Description: High concentration photovoltaics (HCPV) promise a more efficient, higher power output than traditional photovoltaic modules. This is achieved by concentrating sunlight onto a small 1 cm2 triple junction (CTJ) InGaP/InGaAs/Ge cell by using precision optics. In order to achieve high performance, careful and informed design decisions must be made in the development of a HCPV module . This project investigated the design of a HCPV module and is divided into sections that concentrate on the optical design, thermal dissipation and electrical characterization of a concentration triple junction cell. The first HCPV module (Module I) design was based on the Sandia III Baseline Fresnel module which comprised of a Fresnel lens and truncated reflective secondary as the optical elements. The parameters of the CTJ cell in Module I increased with increased concentration. This included the short circuit current, open circuit voltage, power and efficiency. The best performance achieved was at 336 times operational concentration which produced 10.3 W per cell, a cell efficiency of 38.4 percent, and module efficiency of 24.2 percent Investigation of the optical subsystem revealed that the optics played a large role in the operation of the CTJ cell. Characterization of the optical elements showed a transmission loss of 15 percent of concentrated sunlight for the irradiance of which 66 percent of the loss occurred in wavelength region where the InGaP subcell is active. Characterization of the optical subsystem indicated regions of non-uniform irradiance and spectral intensity across the CTJ cell surface. The optical subsystem caused the InGaP subcell of the series monolithic connected CTJ cell to be current limiting. This was confirmed by the CTJ cell having the same short circuit current as the InGaP subcell. The performance of the CTJ cell decreased with an increase in operational temperature. A form of thermal dissipation was needed as 168 times more heat needs to be dissipated when compared to a flat plate photovoltaic module. The thermal dissipation was achieved by passive means with a heat sink which reduced the operational temperature of the CTJ cell from 50 oC to 21 oC above ambient. Cell damage was noted in Module I due to bubbles in the encapsulation epoxy bursting from a high, non-uniform intensity distribution. The development of the second module (Module II) employed a pre-monitoring criteria that characterized the CTJ cells and eliminated faulty cells from the system. These criteria included visual inspection of the cell, electroluminescence and one sun current-voltage (I-V) characteristic curves. Module II was designed as separate units which comprised of a Fresnel lens, refractive secondary, CTJ cell and heatsink. The optimal configuration between the two modules were compared. The CTJ cells in module II showed no form of degradation in the I-V characteristics and in the detected defects. The units under thermal and optical stress showed a progressive degradation. A feature in the I-V curve at V > Vmax was noted for the thermally stressed unit. This feature in the I-V curve may be attributed to the breakdown of the Ge subcell in the CTJ cell. Based on the results obtained from the two experimental HCPV modules, recommendations for an optimal HCPV module were made.
- Full Text:
- Date Issued: 2012
On the optical and electrical design of low concentrator photovoltaic modules
- Authors: Benecke, Mario Andrew
- Date: 2012
- Subjects: Photovoltaic cells -- Design and construction , Photovoltaic cells
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:10543 , http://hdl.handle.net/10948/d1013102
- Description: The increasing interest in non-fossil fuel based electricity generation has caused a prominent boost for the renewable energy sector, especially the field of Photovoltaics (PV) with one of the main reasons being the decrease in cost of PV electricity generation. However, over the last few years a saturation in the efficiency of solar cells have been reached leading into a renewed search for other means to further reduce the cost of electricity generation from photovoltaic sources. One of the technologies that has attracted a lot of attention is low concentration photovoltaics (LCPV). LCPV investigates an alternative strategy to replace costly semiconductor material with relatively cheap optical materials by developing a Low Concentration Photovoltaic (LCPV) module. A LCPV module is divided into three subsystems, namely, the optical, electrical and thermal subsystem. This study focussed on the design, construction and characterisation of an optical subsystem accompanied by a thorough investigation into the design of an electrical subsystem. A facetted parabolic concentrator using a vertical receiver was modelled and a first prototype was constructed having a geometric concentration factor of 6.00 X. Upon electrical characterisation of this first vertical receiver LCPV prototype a concentration of only 4.53 X (receiver 1) and 4.71 X (receiver 2) was obtained. The first vertical receiver LCPV prototype did not reach the expected concentration factor due to optical losses and misalignment of optical elements. The illumination profile obtained from the reflector element was investigated and an undesirable non-uniform illumination profile was discovered. A second vertical receiver LCPV prototype was constructed in an attempt to improve on the first prototype, this second vertical receiver prototype had a geometrical concentration factor of 5.80 X. The results indicated a much improved illumination profile, yet still containing a number of non-uniformities. The second vertical receiver LCPV module yielded an operational concentration factor of 5.34 X. From the preliminary results obtained it was discovered that under concentrated illumination there was a limitation on the maximum power that could be obtained from the receiver. Upon further investigation it was discovered that this limitation was due to the higher current levels under concentrated illumination accompanied by a high series resistance of the receiver. This lead to the construction of new PV receivers, where this limitation could be minimised. 3 cell, 4 cell, 6 cell and 8 cell string configurations were constructed and used for the electrical characterisation of the prototypes. Due to non-uniformity of the illumination profile obtained from the second LCPV prototype a third vertical receiver LCPV prototype was constructed. This vertical receiver design illustrated more uniformity in the obtained illumination distribution and had a geometrical concentration factor of 4.61 X, although under operation only 4.26 X could be obtained. It is important to note that the geometric concentration factor does not account for reflective losses of the reflective material. One of the main reasons for the difficulty in obtaining a uniform illumination profile with the vertical receiver design is that the facetted reflector element is far away from the PV receiver. This enhances the effect of the slightest misalignment of any of the optical elements. This large distance also increases the effect of lensing from each facet. These factors lead to the consideration of a second design, which would counteract these factors. A horizontal receiver LCPV module design implementing a facetted parabolic reflector was considered to counteract these effects. From a mathematical model a horizontal receiver LCPV prototype was constructed having a geometrical concentration factor 5.3 X. The optical characterisation of the illumination profile showed a much improved illumination profile, which was much more uniform than the previous illumination profiles obtained from the other LCPV prototypes. The uniformity of the illumination profile could be seen in results obtained from the electrical characterisation where the concentrator reached operational concentration factor of 5.01 X. The reliability of the third vertical receiver LCPV prototype and the horizontal receiver LCPV prototype as well as the receivers were investigated by placing each receiver under stressed operational conditions for 60 sun hours. I-V characteristics were obtained after every five sun hours to investigate any signs of degradation. After 60 sun hours none of the receiver displayed any signs of degradation or reduction in electrical performance.
- Full Text:
- Date Issued: 2012