Electrospun nanofibers as solid phase extraction sorbents and support for alkylphenols colorimetric probes
- Authors: Tancu, Yolanda
- Date: 2014
- Subjects: Nanofibers , Electrospinning , Extraction (Chemistry) , Sorbents , Phenols , Colorimetry , Transmission electron microscopy , High resolution spectroscopy
- Language: English
- Type: Thesis , Doctoral , PhD
- Identifier: vital:4486 , http://hdl.handle.net/10962/d1012997
- Description: The thesis reports on fabricating alternative solid phase extraction (SPE) sorbents and colorimetric probes based on electrospun nanofibers for alkylphenols (APs). Hydroxyl methylated styrene [poly(co-styrene-CH₃OH)] and 3-oxobutanoate styrene [poly(co-styrene-OCOCH₃COCH₃)] copolymers were synthesized and fabricated into sorbent materials by electro-spinning/spraying. The fabricated morphologies consisting of bead free fibers, beaded fibers and particles were evaluated as SPE sorbents using batch experiments. Electropun fibers proved to be better sorbents as they exhibited extraction efficiency that exceeded 95% compared to 60% for beaded fibers and 40% for particles. In view to reduce sample and solvent volumes, smooth fibers were packed into pipette tips as SPE devices that yielded quantitative recoveries of APs from spiked wastewater samples. Recoveries ranged from 70% to 125% with LOD of 0.008, 0.01 and 0.1 μg mL⁻¹ for 4-tert octylphenol (4-t-OP), 4-octylphenol (4-OP) and 4-nonylphenol (4-NP) respectively, when using high performance liquid chromatography-fluorescence detector (HPLC-FLD). Furthermore, amino functionalised polydiacetylene polymers (PDAs), citrate capped gold (AuNPs) and silver nanoparticles (AgNPs) were evaluated as colorimetric probes for visual detection of APs. In colloidal studies, AuNPs probe showed a colour change from wine red to green upon introduction of analyte. UV-vis spectroscopy revealed the shifting of the surface plasmon resonance (SPR) peak from 525 nm to 729 nm induced by aggregation of AuNPs. For AgNPs probe, a colour change was observed from yellowish green to brown. Transmission electron microscopy (TEM) studies showed growth of AgNPs. A presumed oxidation of the analyte, forming an absorbing compound at 279 nm in both AgNPs and PDAs probes was also observed. For PDAs probe the colour change was from purple to pink. Concentrations as low as 30 μg mL⁻¹ were detectable in all colloidal based probes. Further colorimetric investigations were conducted with electrospun AuNPs-nylon 6 fiber mat. A colour change from purplish red to navy blue at concentrations of 1000 μg mL⁻¹ was observed. Electrospun AgNPs –nylon 6 fiber mat did not show a distinct colour change. High resolution scanning electron microscopy (HRSEM) revealed the analyte inducing the assembly of AuNPs and AgNPs as they covered the surface of the nanofiber mat. Electrospun nanofibers are a platform for analysis and thus tuning their chemistry will lead to sensitive and selective methods
- Full Text:
- Date Issued: 2014
- Authors: Tancu, Yolanda
- Date: 2014
- Subjects: Nanofibers , Electrospinning , Extraction (Chemistry) , Sorbents , Phenols , Colorimetry , Transmission electron microscopy , High resolution spectroscopy
- Language: English
- Type: Thesis , Doctoral , PhD
- Identifier: vital:4486 , http://hdl.handle.net/10962/d1012997
- Description: The thesis reports on fabricating alternative solid phase extraction (SPE) sorbents and colorimetric probes based on electrospun nanofibers for alkylphenols (APs). Hydroxyl methylated styrene [poly(co-styrene-CH₃OH)] and 3-oxobutanoate styrene [poly(co-styrene-OCOCH₃COCH₃)] copolymers were synthesized and fabricated into sorbent materials by electro-spinning/spraying. The fabricated morphologies consisting of bead free fibers, beaded fibers and particles were evaluated as SPE sorbents using batch experiments. Electropun fibers proved to be better sorbents as they exhibited extraction efficiency that exceeded 95% compared to 60% for beaded fibers and 40% for particles. In view to reduce sample and solvent volumes, smooth fibers were packed into pipette tips as SPE devices that yielded quantitative recoveries of APs from spiked wastewater samples. Recoveries ranged from 70% to 125% with LOD of 0.008, 0.01 and 0.1 μg mL⁻¹ for 4-tert octylphenol (4-t-OP), 4-octylphenol (4-OP) and 4-nonylphenol (4-NP) respectively, when using high performance liquid chromatography-fluorescence detector (HPLC-FLD). Furthermore, amino functionalised polydiacetylene polymers (PDAs), citrate capped gold (AuNPs) and silver nanoparticles (AgNPs) were evaluated as colorimetric probes for visual detection of APs. In colloidal studies, AuNPs probe showed a colour change from wine red to green upon introduction of analyte. UV-vis spectroscopy revealed the shifting of the surface plasmon resonance (SPR) peak from 525 nm to 729 nm induced by aggregation of AuNPs. For AgNPs probe, a colour change was observed from yellowish green to brown. Transmission electron microscopy (TEM) studies showed growth of AgNPs. A presumed oxidation of the analyte, forming an absorbing compound at 279 nm in both AgNPs and PDAs probes was also observed. For PDAs probe the colour change was from purple to pink. Concentrations as low as 30 μg mL⁻¹ were detectable in all colloidal based probes. Further colorimetric investigations were conducted with electrospun AuNPs-nylon 6 fiber mat. A colour change from purplish red to navy blue at concentrations of 1000 μg mL⁻¹ was observed. Electrospun AgNPs –nylon 6 fiber mat did not show a distinct colour change. High resolution scanning electron microscopy (HRSEM) revealed the analyte inducing the assembly of AuNPs and AgNPs as they covered the surface of the nanofiber mat. Electrospun nanofibers are a platform for analysis and thus tuning their chemistry will lead to sensitive and selective methods
- Full Text:
- Date Issued: 2014
Electrospun sorbents for solid phase extraction (SPE) and colorimetric detection of pesticides
- Authors: Gulamussen, Noor Jehan
- Date: 2014
- Subjects: Sorbents , Electrospinning , Extraction (Chemistry) , Colorimetry , Pesticides , Water -- Pesticide content -- Research
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4501 , http://hdl.handle.net/10962/d1013241
- Description: The thesis presents the evaluation of polysulfone sorbents for solid phase extraction (SPE) and the development of colorimetric probes for pesticides analysis in water. Through electrospraying and electrospinning techniques, different morphologies of sorbents (particles, beaded fibers and bead-free fibers) were fabricated. The sorbents were morphologically characterized by scanning electron microscopy. Adsorption capacities of sorbents were evaluated by conducting recoveries studies for model pesticides; atrazine, chlorpyrifos and DDT using batch and column SPE modes. Better recovery results were achieved by employing the batch mode of fibers, as values ranged from 98 to 105percent. Further sorbent evaluation was conducted using breakthrough experiments and static experiments. The breakthrough studies indicated that 1700 μL was the sample volume that could be percolated with no breakthrough of the analyte that correspond to a concentration of 150 mg/g of sorbent that can be extracted without any loss of analyte. From static studies, quantities of each model compound adsorbed into the fiber at the equilibrium time were evaluated. The adsorbed atrazine was 65, chlorpyrifos 250 and DDT 400 mg/g of sorbent. Kinetic studies suggested retention mechanism following pseudo first and second order model observed by high correlation coefficients (> 0. 96), demonstrating the fiber affinity to retain both polar and non-polar compounds opening a possibility to be used as sorbent for sample preparation of different classes of pesticides in water. For the second part of the study simple strategies for colorimetric sensing based on silver nanoparticles and polivinylpyrrolidone capped nanoparticles were developed, respectively for atrazine and chlorpyrifos detection. The limits of detection of the methods were 3.32 and 0.88 mg/L for atrazine and chlorpyrifos respectively. The applicability of the probe in real samples was demonstrated by the recoveries studies of tap water varying from 94 to 104 percent. The versatility of the probe was demonstrated by affording a simple, rapid and selective detection of atrazine and chlorpyrifos in the presence of other pesticides by direct analysis without employing any sample handling steps. Attempt to incorporate the probes in a solid support was achieved by using nylon 6 as solid support polymer proving to be fast and useful for on-site detection.
- Full Text:
- Date Issued: 2014
- Authors: Gulamussen, Noor Jehan
- Date: 2014
- Subjects: Sorbents , Electrospinning , Extraction (Chemistry) , Colorimetry , Pesticides , Water -- Pesticide content -- Research
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4501 , http://hdl.handle.net/10962/d1013241
- Description: The thesis presents the evaluation of polysulfone sorbents for solid phase extraction (SPE) and the development of colorimetric probes for pesticides analysis in water. Through electrospraying and electrospinning techniques, different morphologies of sorbents (particles, beaded fibers and bead-free fibers) were fabricated. The sorbents were morphologically characterized by scanning electron microscopy. Adsorption capacities of sorbents were evaluated by conducting recoveries studies for model pesticides; atrazine, chlorpyrifos and DDT using batch and column SPE modes. Better recovery results were achieved by employing the batch mode of fibers, as values ranged from 98 to 105percent. Further sorbent evaluation was conducted using breakthrough experiments and static experiments. The breakthrough studies indicated that 1700 μL was the sample volume that could be percolated with no breakthrough of the analyte that correspond to a concentration of 150 mg/g of sorbent that can be extracted without any loss of analyte. From static studies, quantities of each model compound adsorbed into the fiber at the equilibrium time were evaluated. The adsorbed atrazine was 65, chlorpyrifos 250 and DDT 400 mg/g of sorbent. Kinetic studies suggested retention mechanism following pseudo first and second order model observed by high correlation coefficients (> 0. 96), demonstrating the fiber affinity to retain both polar and non-polar compounds opening a possibility to be used as sorbent for sample preparation of different classes of pesticides in water. For the second part of the study simple strategies for colorimetric sensing based on silver nanoparticles and polivinylpyrrolidone capped nanoparticles were developed, respectively for atrazine and chlorpyrifos detection. The limits of detection of the methods were 3.32 and 0.88 mg/L for atrazine and chlorpyrifos respectively. The applicability of the probe in real samples was demonstrated by the recoveries studies of tap water varying from 94 to 104 percent. The versatility of the probe was demonstrated by affording a simple, rapid and selective detection of atrazine and chlorpyrifos in the presence of other pesticides by direct analysis without employing any sample handling steps. Attempt to incorporate the probes in a solid support was achieved by using nylon 6 as solid support polymer proving to be fast and useful for on-site detection.
- Full Text:
- Date Issued: 2014
A study of electrospun nanofibers and diatomaceous earth materials for the extraction of alkaloids, flavonoids and aromatic amines in various matrices
- Mothibedi, Kediemetse (Kedimetse)
- Authors: Mothibedi, Kediemetse (Kedimetse)
- Date: 2013 , 2013-04-07
- Subjects: Nanofibers , Electrospinning , Sorbents , Extraction (Chemistry) , Alkaloids , Flavonoids , Amines , Matrices , Goldenseal , Ginkgo , Dyes and dyeing -- Chemistry
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4288 , http://hdl.handle.net/10962/d1003052 , Nanofibers , Electrospinning , Sorbents , Extraction (Chemistry) , Alkaloids , Flavonoids , Amines , Matrices , Goldenseal , Ginkgo , Dyes and dyeing -- Chemistry
- Description: The thesis explored the use of different sorbent materials in solid phase extraction method development. The methods included the use of the polymeric Agilent Bond Elut Plexa solid phase extraction and electrospun polymer-silica composite sorbents for clean-up and preconcentration. Sample clean-up for alkaloids (hydrastine and berberine) in goldenseal, Hydrastis canadensis and flavonoids (quercetin, kaempferol and isorhamnetin) in Ginkgo biloba was achieved using Bond Elut Plexa SPE sorbent. Clean-up of flavonoids in Ginkgo biloba was also achieved using electrospun polymer-silica composite (polystyrene-silica, polyacrylonitrile-silica and nylon 6-silica) sorbents. All analysis of flavonoids and alkaloids was carried out using an Agilent 1200 Series HPLC coupled with a diode array detector. Good peak separation was achieved in less than 6 min employing an Agilent ZORBAX Eclipse Plus C18 column (4.6 x 75 mm, 3.5 μm) at 35⁰C. The mobile phases employed were 0.1% phosphoric acid/methanol gradient and 0.5% phosphoric acid/methanol (40:60) for alkaloids and flavonoids respectively. The calibration curves exhibited linearity up to 120 μg mL⁻¹ with correlation coefficients of more than 0.9980. The recoveries ranged from 73-109% with relative standard deviation of less than 5% for all analytes. Agilent Chem Elut supported liquid extraction was employed for the development of a sample preparation method for the determination of 24 banned aromatic amines from azo dyes in textile following the EU standard method EN 14362-1:2003 (E) and the Chinese standard method GB/T 17592-2006. The supported liquid extraction was effective in the extraction of the aromatic amines from textile (cotton, wool and polyester/cotton [80%:20%]). Most of the recoveries obtained were conforming to the minimum requirements set in the EN 14362-1:2003 (E) standard method and the relative standard deviations were less than 15%. Good peak separation was obtained within 70 min run time using the Agilent Zorbax SB-Phenyl column (4.6 mm x 250 mm, 5-micron) or the Agilent DB-35 MS (J & W) (30 m x 0.25 mm, 0.25 μm film thickness. It was demonstrated that the polymeric Agilent Bond Elut Plexa, electrospun nanofibers and diatomaceous earth were effective in extraction of alkaloids, flavonoids and aromatic amines in different matrices. The developed methods were simple, rapid and reproducible.
- Full Text:
- Date Issued: 2013
- Authors: Mothibedi, Kediemetse (Kedimetse)
- Date: 2013 , 2013-04-07
- Subjects: Nanofibers , Electrospinning , Sorbents , Extraction (Chemistry) , Alkaloids , Flavonoids , Amines , Matrices , Goldenseal , Ginkgo , Dyes and dyeing -- Chemistry
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4288 , http://hdl.handle.net/10962/d1003052 , Nanofibers , Electrospinning , Sorbents , Extraction (Chemistry) , Alkaloids , Flavonoids , Amines , Matrices , Goldenseal , Ginkgo , Dyes and dyeing -- Chemistry
- Description: The thesis explored the use of different sorbent materials in solid phase extraction method development. The methods included the use of the polymeric Agilent Bond Elut Plexa solid phase extraction and electrospun polymer-silica composite sorbents for clean-up and preconcentration. Sample clean-up for alkaloids (hydrastine and berberine) in goldenseal, Hydrastis canadensis and flavonoids (quercetin, kaempferol and isorhamnetin) in Ginkgo biloba was achieved using Bond Elut Plexa SPE sorbent. Clean-up of flavonoids in Ginkgo biloba was also achieved using electrospun polymer-silica composite (polystyrene-silica, polyacrylonitrile-silica and nylon 6-silica) sorbents. All analysis of flavonoids and alkaloids was carried out using an Agilent 1200 Series HPLC coupled with a diode array detector. Good peak separation was achieved in less than 6 min employing an Agilent ZORBAX Eclipse Plus C18 column (4.6 x 75 mm, 3.5 μm) at 35⁰C. The mobile phases employed were 0.1% phosphoric acid/methanol gradient and 0.5% phosphoric acid/methanol (40:60) for alkaloids and flavonoids respectively. The calibration curves exhibited linearity up to 120 μg mL⁻¹ with correlation coefficients of more than 0.9980. The recoveries ranged from 73-109% with relative standard deviation of less than 5% for all analytes. Agilent Chem Elut supported liquid extraction was employed for the development of a sample preparation method for the determination of 24 banned aromatic amines from azo dyes in textile following the EU standard method EN 14362-1:2003 (E) and the Chinese standard method GB/T 17592-2006. The supported liquid extraction was effective in the extraction of the aromatic amines from textile (cotton, wool and polyester/cotton [80%:20%]). Most of the recoveries obtained were conforming to the minimum requirements set in the EN 14362-1:2003 (E) standard method and the relative standard deviations were less than 15%. Good peak separation was obtained within 70 min run time using the Agilent Zorbax SB-Phenyl column (4.6 mm x 250 mm, 5-micron) or the Agilent DB-35 MS (J & W) (30 m x 0.25 mm, 0.25 μm film thickness. It was demonstrated that the polymeric Agilent Bond Elut Plexa, electrospun nanofibers and diatomaceous earth were effective in extraction of alkaloids, flavonoids and aromatic amines in different matrices. The developed methods were simple, rapid and reproducible.
- Full Text:
- Date Issued: 2013
The development of platinum and palladium-selective polymeric materials
- Authors: Fayemi, Omolola Esther
- Date: 2013 , 2013-05-03
- Subjects: Polymers , Platinum , Palladium , Adsorption , Sorbents , Nanofibers , Amines , Nanoparticles
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4287 , http://hdl.handle.net/10962/d1002964 , Polymers , Platinum , Palladium , Adsorption , Sorbents , Nanofibers , Amines , Nanoparticles
- Description: The adsorption and separation of platinum(IV) and palladium(II) chlorido species (PtCl₆²⁻ and PdCl₄²⁻) on polystyrene-based beads and nanofibers as well as silica microparticles functionalized with polyamine centres derived from ethylenediamine (EDA), diethylenetriamine (DETA), triethylenetriamine (TETA) and tris-(2-aminoethyl)amine (TAEA) is described. The functionalized sorbent materials were characterized by using microanalysis, SEM, XPS, BET and FTIR. The nanofiber sorbent material functionalized with ethylenediamine (F-EDA) had the highest loading capacity which was attributed to its high nitrogen content (10.83%) and larger surface area (241.3m²/g). The adsorption and loading capacities of the sorption materials were investigated using both the batch and column studies in 1 M HCI. The adsorption studies for both PtCl₆²⁻ and PdCl₄²⁻ on the polystyrene-based sorbent materials fit the Langmuir isotherm while the silica-based sorbents fitted the Freundlich isotherm with R² values > 0.99. In the column experiment the highest loading capacity of Pt and Pd were 7.4 mg/g and 4.3 mg/g respectively on the nanofiber sorbent material based on ethylenediamine (EDA). The polystyrene and silica-based resins with triethylenetetramine (TETA) functionality (M-TETA and S-TETA) showed selectivity for platinum and palladium, respectively. Metal chlorido complexes loaded on the sorbent materials were recovered by using 3% m/v thiourea solution as teh eluting agent with quantitative desorption efficiency under the selected experimental conditions. The separation of platinum from palladium was partially achieved by selective stripping of PtCl₆²⁻ with 0.5 M of NaClO₄ in 1.0 M HCI with PdCl₄²⁻ was eluted with 0.5 M thiourea in 1.0 M HCI. The selectivity of the M-TETA and S-TETA sorbent materials was proved by column separation of platinum(IV) and palladium(II), respectively, from synthetic solutions containing iridium(IV) and rhodium(III). The loading capacity for platinum on M-TETA was 0.09 mg/g while it was 0.27 mg/g for palladium on S-TETA. , Acrobat PDFMaker 10.1 for Word , Adobe Acrobat 9.54 Paper Capture Plug-in
- Full Text:
- Date Issued: 2013
- Authors: Fayemi, Omolola Esther
- Date: 2013 , 2013-05-03
- Subjects: Polymers , Platinum , Palladium , Adsorption , Sorbents , Nanofibers , Amines , Nanoparticles
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4287 , http://hdl.handle.net/10962/d1002964 , Polymers , Platinum , Palladium , Adsorption , Sorbents , Nanofibers , Amines , Nanoparticles
- Description: The adsorption and separation of platinum(IV) and palladium(II) chlorido species (PtCl₆²⁻ and PdCl₄²⁻) on polystyrene-based beads and nanofibers as well as silica microparticles functionalized with polyamine centres derived from ethylenediamine (EDA), diethylenetriamine (DETA), triethylenetriamine (TETA) and tris-(2-aminoethyl)amine (TAEA) is described. The functionalized sorbent materials were characterized by using microanalysis, SEM, XPS, BET and FTIR. The nanofiber sorbent material functionalized with ethylenediamine (F-EDA) had the highest loading capacity which was attributed to its high nitrogen content (10.83%) and larger surface area (241.3m²/g). The adsorption and loading capacities of the sorption materials were investigated using both the batch and column studies in 1 M HCI. The adsorption studies for both PtCl₆²⁻ and PdCl₄²⁻ on the polystyrene-based sorbent materials fit the Langmuir isotherm while the silica-based sorbents fitted the Freundlich isotherm with R² values > 0.99. In the column experiment the highest loading capacity of Pt and Pd were 7.4 mg/g and 4.3 mg/g respectively on the nanofiber sorbent material based on ethylenediamine (EDA). The polystyrene and silica-based resins with triethylenetetramine (TETA) functionality (M-TETA and S-TETA) showed selectivity for platinum and palladium, respectively. Metal chlorido complexes loaded on the sorbent materials were recovered by using 3% m/v thiourea solution as teh eluting agent with quantitative desorption efficiency under the selected experimental conditions. The separation of platinum from palladium was partially achieved by selective stripping of PtCl₆²⁻ with 0.5 M of NaClO₄ in 1.0 M HCI with PdCl₄²⁻ was eluted with 0.5 M thiourea in 1.0 M HCI. The selectivity of the M-TETA and S-TETA sorbent materials was proved by column separation of platinum(IV) and palladium(II), respectively, from synthetic solutions containing iridium(IV) and rhodium(III). The loading capacity for platinum on M-TETA was 0.09 mg/g while it was 0.27 mg/g for palladium on S-TETA. , Acrobat PDFMaker 10.1 for Word , Adobe Acrobat 9.54 Paper Capture Plug-in
- Full Text:
- Date Issued: 2013
Solid-phase extraction based sample preparation for the determination of drug and organic pollutant residue
- Authors: Pule, Bellah Oreeditse
- Date: 2011 , 2011-02-08
- Subjects: Food contamination , Drugs -- Analysis , Pharmaceutical chemistry , Extraction (Chemistry) , Sorbents
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4406 , http://hdl.handle.net/10962/d1006711 , Food contamination , Drugs -- Analysis , Pharmaceutical chemistry , Extraction (Chemistry) , Sorbents
- Description: This thesis presents solid phase extraction (SPE) methodologies based on mixed-mode polymeric sorbents; a mixed mode strong anion exchanger (Agilent SampliQ SAX) and a mixed mode strong cation exchanger (Agilent SampliQ SCX). Furthermore, dispersive-SPE based on a quick, easy, cheap, effective, rugged and safe (QuEChERS) method was assessed for applicability in the determination of drug residues. The mixed-mode polymeric sorbents were evaluated for the simultaneous fractionation of drugs that exhibit diverse polarities with acidic, basic and neutral functionalities in biological matrices (plasma and urine). The polymeric skeleton of these sorbents entails an exchanger group and therefore provides two retention mechanisms, strong cation or anion exchange retention mechanisms with hydrophobic interactions. It was demonstrated that with a sequential elution protocol for sample clean-up analytes were fractionated into acidic, basic and neutral classes. The SAX was employed for analysis of ketoprofen, naproxen (acidic drugs), nortriptyline (basic) and secobarbital (neutral) from urine sample. The SCX was used for fractionating phenobarbital, p-toluamide (acidic), amphetamine, m-toluidine (basic) and acetaminophen (neutral drug) from plasma sample. QuEChERS method was employed for quantitative determination of 16 polycyclic aromatic hydrocarbons (PAHs) from fish fillets and soil; 9 sulfonamides (SAs) from chicken muscles and acrylamide (AA) in cooking oil. The analyte recoveries ranged from 79.6 - 109% with RSDs ranging from 0.06 - 1.9% at three different fortification levels. Good linearity (r2 > 0.9990) was attained for most analytes. The limits of detection and quantification ranged from 0.03 - 0.84 μg/ml and 0.81 - 1.89 μg/ml respectively for analytes in biological samples. LODs and LOQs for analytes in food and environmental samples ranged from 0.02 to 0.39 and 0.25 to 1.30 ng/g respectively.
- Full Text:
- Date Issued: 2011
- Authors: Pule, Bellah Oreeditse
- Date: 2011 , 2011-02-08
- Subjects: Food contamination , Drugs -- Analysis , Pharmaceutical chemistry , Extraction (Chemistry) , Sorbents
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4406 , http://hdl.handle.net/10962/d1006711 , Food contamination , Drugs -- Analysis , Pharmaceutical chemistry , Extraction (Chemistry) , Sorbents
- Description: This thesis presents solid phase extraction (SPE) methodologies based on mixed-mode polymeric sorbents; a mixed mode strong anion exchanger (Agilent SampliQ SAX) and a mixed mode strong cation exchanger (Agilent SampliQ SCX). Furthermore, dispersive-SPE based on a quick, easy, cheap, effective, rugged and safe (QuEChERS) method was assessed for applicability in the determination of drug residues. The mixed-mode polymeric sorbents were evaluated for the simultaneous fractionation of drugs that exhibit diverse polarities with acidic, basic and neutral functionalities in biological matrices (plasma and urine). The polymeric skeleton of these sorbents entails an exchanger group and therefore provides two retention mechanisms, strong cation or anion exchange retention mechanisms with hydrophobic interactions. It was demonstrated that with a sequential elution protocol for sample clean-up analytes were fractionated into acidic, basic and neutral classes. The SAX was employed for analysis of ketoprofen, naproxen (acidic drugs), nortriptyline (basic) and secobarbital (neutral) from urine sample. The SCX was used for fractionating phenobarbital, p-toluamide (acidic), amphetamine, m-toluidine (basic) and acetaminophen (neutral drug) from plasma sample. QuEChERS method was employed for quantitative determination of 16 polycyclic aromatic hydrocarbons (PAHs) from fish fillets and soil; 9 sulfonamides (SAs) from chicken muscles and acrylamide (AA) in cooking oil. The analyte recoveries ranged from 79.6 - 109% with RSDs ranging from 0.06 - 1.9% at three different fortification levels. Good linearity (r2 > 0.9990) was attained for most analytes. The limits of detection and quantification ranged from 0.03 - 0.84 μg/ml and 0.81 - 1.89 μg/ml respectively for analytes in biological samples. LODs and LOQs for analytes in food and environmental samples ranged from 0.02 to 0.39 and 0.25 to 1.30 ng/g respectively.
- Full Text:
- Date Issued: 2011
- «
- ‹
- 1
- ›
- »