Higher order modulation formats for high speed optical communication systems with digital signal processing aided receiver
- Authors: Chabata, Tichakunda Valentine
- Date: 2016
- Subjects: Optical communications , Modulation (Electronics) , Signal processing
- Language: English
- Type: Thesis , Doctoral , PhD
- Identifier: http://hdl.handle.net/10948/4775 , vital:20677
- Description: The drastic increase in the number of internet users and the general convergence of all other communication systems into an optical system have brought a sharp rise in demand for bandwidth and calls for high capacity transmission networks. Large unamplified transmission reach is another contributor in reducing deployment costs of an optical communication system. Spectrally efficient modulation formats are suggested as a solution to overcome the problems associated with limited channels and bandwidth of dense wavelength division multiplexing (DWDM) optical communication systems. Higher order modulation formats which are considered to be spectrally efficient and can increase the transmission capacity by transmitting more information in the amplitude, phase, polarization or a combination of all was studied. Different detection technologies are to be implemented to suit a particular higher order modulation format. In this research multilevel modulation formats, different detection technologies and a digital signal processing aided receiver were studied in a practical optical transmission system. The work in this thesis started with the implementation of the traditional amplitude shift keying (ASK) modulation and a differential phase shift keying (DPSK) modulation systems as they form the basic building block in the design of higher order modulation formats. Results obtained from using virtual photonics instruments (VPI)simulation software, receiver sensitivity for 10Gbpsnon-return-to-zero (NRZ), amplitude phase shift keying (ASK) and DPSK signals were measured to be -22.7 dBm and -22.0 dBm respectively. Performance comparison for the two modulation formats were done over different transmission distances. ASK also known as On-Off keying (OOK) performed better for shorter lengths whereas DPSK performed better for longer lengths of up to90km.Experimental results on a 10 Gbps NRZ- ASK signal gave a receiver sensitivity of -21.1 dBm from digital signal processing (DSP) aided receiver against -19.8 dBm from the commercial bit error ratio tester (BERT) yielding a small difference of 1.3 dB hence validating the reliability and accuracy of the digital signal processing (DSP) assisted receiver. Traditional direct detection scheme and coherent detection scheme performances were evaluated again on a 10 Gbps NRZ ASK signal. Coherent detection that can achieve a large unamplified transmission reach and has a higher passive optical splitting ratio was first evaluated using the VPI simulation software. Simulation results gave a receiver sensitivity of -30.4 dBm forcoherent detection and -18.3 dBm for direct detection, yielding a gain in receiver sensitivity of 12.1 dB. The complex coherently detected signal, from the experimental setup gave a receiver sensitivity of -20.6 dBm with a gain in receiver sensitivity of 3.5 dBm with respect to direct detection. A multilevel pulse amplitude modulation (4-PAM) that doubles the data rate per channel from10 Gbps to 20 Gbps by transmitting more information in the amplitude of the carrier signal was implemented. This was achieved by modulating the optical amplitude with an electrical four level amplitude shift keyed (ASK) signal. A receiver consisting of a single photodiode, three decision circuits and a decoding logic circuit was used to receive and extract the original transmitted data. A DSP aided receiver was used to evaluate the link performance. A receiver sensitivity of -12.8 dBm is attained with a dispersion penalty of about 7.2 dB after transmission through 25 km of G.652 fibre.
- Full Text:
- Date Issued: 2016
Fibre optic network supporting high speed transmission in the square kilometre array, South Africa
- Authors: Rotich, Enoch Kirwa
- Date: 2015
- Subjects: Optical communications , Fiber optics , Telecommunication systems
- Language: English
- Type: Thesis , Doctoral , PhD
- Identifier: http://hdl.handle.net/10948/6552 , vital:21109
- Description: This thesis provides in-depth information on the high speed optical transport requirements for the Square Kilometre Array. The stringent data rates as well as timing and synchronization requirements are dealt with respect to the optical fibre technology. Regarding the data transport, we draw a clear comparison between a typical telecommunication access network and a telescope network. Invoking simulations and experiments on the field and laboratory test bed, we successfully implement a suitable telescope network using vertical cavity surface emitting laser (VCSEL) technology. Polarization effects on the KAT-7 telescope network, an operational prototype for the SKA is studied so as to estimate the expected effect in the MeerKAT telescope with transmission distances _ 12 km. The study further relates the obtained values to the expected impact on the distribution of the time and frequency reference in the MeerKAT array. Clock stability depends on the differential group delay (DGD) and polarization stability. On a 10:25 km link that includes the riser cable a DGD of 62:1 fs was attained. This corresponds to a polarization mode dispersion (PMD) coefficient of 19:4 fs=km1=2. This is a low PMD value considering telecommunication network. The PMD value is within the allowed budget in the telescope network. However, this may not be the case at longer baselines extending to over 1000 km as expected in SKA 2. The fibre's deployment contribution to the DGD is measured by comparing the deployed fibre to the undeployed of equal lengths. On the 10:25 km deployed single mode fibre, the maximum and mean DGDs measured were 217:7 fs and 84:8 fs respectively. The undeployed fibre of similar type and equal length, gave a maximum and minimum DGDs of 58:6 fs and 36:3 fs respectively. The deployment is seen to increase the maximum and minimum DGDs by factors of 3.7 and 2.3 respectively. This implies that fibre deployment is very critical in ensuring the birefringence is minimized. Polarization fluctuation recorded a maximum of 180o during the 15 hour real time astronomer use of the antenna. To ascertain the contribution of the riser cable, state of polarization (SOP) of the buried section of the single mode fibre in the link was established. A maximum SOP change of 14o over 15 hour monitoring was measured. From the stability realized on the buried section of the fibre, the change in polarization is contributed by the riser cable. The fluctuation in polarization can cause the phase of a clock signal to drift between the birefringent axes by an equal amount corresponding to DGD. We experimentally demonstrate how polarization stabilization can be attained using the polarization maintaining fibre. We also demonstrate the applicability of VCSEL technology in the SKA unidirectional data flow especially for shorter baselines < 100 km. The VCSEL is a low cost light source with attractive advantages such as low power consumption, high speed capabilities and wavelength tuneability. This work entails the use of traditional amplitude modulation commonly known as non-return-to-zero (NRZ) on-off keying (OOK) because of its simplicity and cost. For the MeerKAT typical distances, we show that even in a worst case scenario, the use of VCSEL on different fibres in MeerKAT distance is achievable. Using the impairment reduction approach, we successfully manage to achieve transmission distance beyond MeerKAT. Several in-line dispersion compensation mechanisms in telecommunication have been successfully employed. The work focused on the use of negative dispersion fibre to mitigate the chromatic dispersion effects in the optical fibre. The inverse dispersion fibre (IDF) is proposed for compensation in the conventional zero dispersion wavelength fibres, G.652 that are used at the third window. Similarly, the chromatic dispersion compensation of non-zero dispersion shifted fibre (NZDSF) is experimentally demonstrated using negative dispersion submarine reduced slope (SRS), G. 655 (-). With dispersion management, we demonstrate how transmissions beyond MeerKAT baselines can be achieved error free. A systematic investigation of the use of distributed Raman amplification to overcome the attenuation losses is provided. High on-off gains of up to 15 dB, 8 dB and 5 dB for bidirectional, forward and backward pumping respectively is achieved on a 25 km Raman optimized NZDSF-Reach fibre. Combined dispersion mitigation technique and low noise distributed Raman amplification, up to about 80 km transmission was achieved on a 4:25 Gbps modulated VCSEL using a single pump. Using bidirectional pumping, more than 100 km of transmission was achieved error free. The high gains enhance the VCSEL transmission distance. We further suggest a novel way of using the Raman pump to distribute the clock signal while amplifying the data signal streaming the astronomical data from the remote placed telescope receivers. In summary, the work presented in this thesis has demonstrated the potential use of VCSEL technology for data collection in the telescope array. We have studied the optical effects and mitigation so as to improve the clock and data transmission. This work is relevant and valuable in providing SKA with VCSELs, an option for extremely high network performance at reasonable costs.
- Full Text:
- Date Issued: 2015
Nonlinear effects with a focus on cross phase modulation and its impact on wavelength division multiplexing optical fibre networks
- Authors: Gamatham, Romeo Reginald Gunther
- Date: 2013
- Subjects: Wavelength division multiplexing , Optical communications , Fiber optics
- Language: English
- Type: Thesis , Doctoral , PhD
- Identifier: http://hdl.handle.net/10948/6302 , vital:21071
- Description: The demand for faster data transmission is ever increasing. Wavelength division multiplexing (WDM) presents as a viable solution to increase the data transmission rate significantly. WDM systems are based on the ability to transmit multiple wavelengths simultaneously down the fibre. Unlike time division multiplexing (TDM) systems, WDM systems do not increase the data transfer by increasing the transmission rate of a single channel. In WDM systems the data rate per channel remains the same, only multiple channels carry data across the link. Dense wavelength division multiplexing (DWDM) promises even more wavelengths packed together in the same fibre. This multiplication of channels increases the bandwidth capacity rapidly. Networks are looking into making use of technology that will ensure no electronic signal regeneration at any point within the DWDM network. Examples are; reconfigurable optical add/drop multiplexers (ROADM) and optical cross connect (OXC) units. These components essentially enable network operators to split, combine and multiplex optical signals carried by optical fibre. WDM allows network operators to increase the capacity of existing networks without expensive re-cabling. This provides networks with the flexibility to be upgraded to larger bandwidths and for reconfiguration of network services. Further, WDM technology opens up an opportunity of marketing flexibility to network operators, where operators not only have the option to rent out cables and fibres but wavelengths as well. Cross phase modulation (XPM) poses a problem to WDM networks. The refractive index experienced by a neighbouring optical signal, not only depends on the signal’s intensity but on the intensity of the co-propagating signal as well. This effect leads to a phase change and is known as XPM. This work investigates the characteristics of XPM. It is shown that, in a two channel WDM network, a probe signal’s SOP can be steered by controlling a high intensity pump signal’s SOP. This effect could be applied to make a wavelength converter. Experimental results show that the degree of polarization (DOP) of a probe signal degrades according to a mathematical model found in literature. The pump and probe signals are shown to experience maximum interaction, for orthogonal probe-pump SOP vector orientations. This may be problematic to polarization mode dispersion compensators. Additionally, experimental results point out that the SOP of a probe signal is much more active in the presence of a high intensity pump, as compared to the single signal transmission scenario.
- Full Text:
- Date Issued: 2013
Effects of polarization in a distributed raman fibre amplifier
- Authors: Muguro, Kennedy Mwaura
- Date: 2011
- Subjects: Fiber optics , Polarization (Light) , Optical communications , Optical amplifiers , Raman effect
- Language: English
- Type: Thesis , Doctoral , PhD
- Identifier: vital:10544 , http://hdl.handle.net/10948/d1014621
- Description: The need to exploit the large fibre bandwidth and increase the reach has seen the application of the Raman fibre amplifier (RFA) become indispensable in modern light wave systems. The success and resilience of RFAs in optical communication is deeply rooted in their unique optical properties and new technologies which have allowed the amplifier to come of age. However, the full potential of RFAs in optical communication and other applications are yet to be realized. More so are its polarization properties which still remain largely unexploited and have not been fully understood. In this work, fundamental issues regarding distributed RFA have been investigated with the aim of acquiring a better understanding of the amplifier polarization characteristics which have potential applications. In particular the effects of polarization mode dispersion (PMD) and polarization dependent loss (PDL) have been demonstrated both by simulation and experiment. The possibility of Raman polarization pulling in single mode fibres (SMFs) has also been addressed. Polarization sensitivity of RFA has been known for a long time but the clear manifestation of it has become evident in the advent of modern low PMD fibre. Unlike EDFAs which make use of special doped fibre, RFAs require no special fibre for operation. Besides, RFA uses a very long length of fibre and as such the fibre polarization characteristics come into play during amplification. In the demonstrations presented in this thesis a fibre of PMD coefficient < 0.05 pskm-1/2 was regarded as low PMD fibre while one having coefficient ≥ 0.05 pskm-1/2 was categorized to have high PMD unless otherwise stated. Several experiments were performed to evaluate the RFA gain characteristics with respect to fibre PMD and the system performance in the presence of noise emanating from amplified spontaneous emission (ASE). Analysis of Raman gain statistics was done for fibres of low and high PMD coefficients. The statistics of PDG and on-off gain were eventually used to demonstrate the extraction of PMD coefficients of fibres between 0.01- 0.1 pskm-1/2 using a forward pumping configuration. It was found that, at increasing pump power a linear relationship exists between forward and backward signal gain on a dB scale. The interaction of PDL and Raman PDG in the presence of PMD were observed at very fundamental level. It was found the presence of PDL serves to reduce the available on-off gain. It was also established that the presence of PMD mediates the interaction between PDG/PDL. When PMD is high it reduces PDG but the presence of PDL introduces a wavelength dependent gain tilting for WDM channels. Further analysis revealed that signal polarization is influenced by the pump SOP due to the pulling effect which is present even at moderate pump power.
- Full Text:
- Date Issued: 2011
Aerial optical fibres in telecommunication systems : SOP and PMD monitoring, and tolerance of modulation formats
- Authors: Ireeta, Winston Tumps
- Date: 2010
- Subjects: Optical communications , Fiber optics
- Language: English
- Type: Thesis , Doctoral , PhD
- Identifier: vital:10542 , http://hdl.handle.net/10948/1478 , http://hdl.handle.net/10948/d1012894 , Optical communications , Fiber optics
- Description: The topic of this thesis is aerial optical fibres in telecommunication systems: state of polarization (SOP) and polarization mode dispersion (PMD) monitoring and tolerance of modulation formats. Errors in optical fibre telecommunication systems are introduced when these polarization effects (SOP and PMD) change. These changes are so intense especially in aerial optical fibres. Part of the backbone of South Africa’s national grid includes long distances of aerial optical fibre between transmission exchange stations. The work in this thesis can be divided into three parts which all deal with the major aspects of PMD in deployed aerial optical fibres: characterization, environmental effects plus other perturbations, and tolerance of different modulation formats. In our work, SOP and PMD field measurements revealed that they both fluctuate more rapidly in deployed aerial optical fibres especially on windy and hot days. The SOP and PMD changes in the aerial optical fibres showed a significant correlation with these environmental parameters. SOP and PMD are stochastic in nature due to changes in the properties of the optical fibres and its positions because of both intrinsic and extrinsic perturbations. In our work, with only 184 PMD values measured and obtained by use of the FTB-5700 single-ended dispersion analyzer, the predicted theoretical Gaussian fit was obtained with a mean of 0.47 ps and standard deviation of 0.08 ps. This small standard deviation was justification for its robustness and accuracy. The statistical distributions for first-order polarization mode dispersion (FO-PMD) and second-order polarization mode dispersion (SO-PMD) for the first time were experimentally confirmed when measured using the FTB-5700 single-ended dispersion analyzer instrument for deployed aerial optical fibres. We were also able to determine the time scale over which to compensate FO-PMD in deployed aerial fibres using the directional time drift autocorrelation function method. It is slightly higher than 390 s for SOP measurements made on a particular windy and hot day. This is due to the fact that the changes of the PMD vector are known to be slower than the SOP changes. vi We also investigated the theoretical statistical distribution that corresponds to output SOP variations. The SOP variations can either be with wavelength (for buried fibre) or with time (for aerial fibre). Our results showed that the statistics of the relative SOP changes approached the distribution proposed by Foschini et al. (2000). Advanced optical modulation formats have become a key ingredient in the design of modern state-of-the-art wavelength-division-multiplexed (WDM) optical transmission systems. In our work, we investigated which of these advanced modulation formats is best suited for the South African network especially on systems that have links of aerial optical fibres. Keywords: aerial optical fibre, polarization mode dispersion (PMD), principal states of polarization (PSP), state of polarization (SOP), first-order PMD, second-order PMD.
- Full Text:
- Date Issued: 2010
Polarization mode dispersion emulation and the impact of high first-order PMD segments in optical telecommunication systems
- Authors: Musara, Vitalis
- Date: 2009
- Subjects: Optical communications , Fiber optics , Polarization (Light)
- Language: English
- Type: Thesis , Doctoral , PhD
- Identifier: vital:10519 , http://hdl.handle.net/10948/1138 , Optical communications , Fiber optics , Polarization (Light)
- Description: In this study, focus is centred on the measurement and emulation of first-order (FO-) and second-order (SO-) polarization mode dispersion (PMD). PMD has deleterious effects on the performance of high speed optical transmission network systems from 10 Gb/s and above. The first step was characterising deployed fibres for PMD and monitoring the state of polarization (SOP) light experiences as it propagates through the fibre. The PMD and SOP changes in deployed fibres were stochastic due to varying intrinsic and extrinsic perturbation changes. To fully understand the PMD phenomenon in terms of measurement accuracy, its complex behaviour, its implications, mitigation and compensation, PMD emulation is crucial. This thesis presents emulator designs which fall into different emulator categories. The key to these designs were the PMD equations and background on the PMD phenomenon. The cross product from the concatenation equation was applied in order to determine the coupling angle β (between 0o and 180o) that results in the SO-PMD of the emulator designs to be either adjustable or fixed. The digital delay line (DDL) or single polarization maintaining fibre (PMF) section was used to give a certain amount of FO-PMD but negligible SO-PMD. PMF sections (birefringent sections) were concatenated together to ensure FO- and SO-PMD coexist, emulating deployed fibres. FO- and SO-PMD can be controlled by altering mode coupling (coupling angles) and birefringence distribution. Emulators with PMD statistics approaching the theoretical distributions had high random coupling and several numbers of randomly distributed PMF sections. In addition, the lengths of their PMF sections lie within 20% standard deviation of the mean emulator length. Those emulators with PMD statistics that did not approach the theoretical distributions had limited numbers of randomly distributed PMF sections and mode coupling. Results also show that even when an emulator has high random mode coupling and several numbers of randomly distributed PMFs, its PMD statistics deviates away from expected theoretical distributions in the presence of polarization dependent loss (PDL). The emulators showed that the background autocorrelation function (BACF) approaches zero with increasing number of randomly mode coupled fibre sections. A zero BACF signifies that an emulator has large numbers of randomly distributed PMF sections and its presence means the opposite. The availability of SO-PMD in the emulators made the autocorrelation function (ACF) x asymmetric. In the absence of SO-PMD the ACF for a PMD emulator is symmetric. SO-PMD has no effect on the BACF. Polarization-optical time domain reflectometry (P-OTDR) measurements have shown that certain fibre sections along fibre link lengths have higher FO-PMD (HiFO-PMD) than other sections. This study investigates the impact of a HiFO-PMD section on the overall FO- and SO-PMD, the output state of polarization (SOP) and system performance on deployed fibres (through emulation). Results show that when the wavelength-independent FO-PMD vector of the HiFO-PMD section is greater than the FO-PMD contributions from the rest of the fibre link, the mean FO-PMD of the entire link is biased towards that of the HiFO-PMD section and the SO-PMD increases (β ≠ 0o or 180o) or remains fixed (β = 0o or 180o) depending on the coupling angle β between the HiFO-PMD section and the rest of the fibre link. In addition, the FO-PMD statistics deviates away from the theoretical Maxwellian distribution. However, experimental results show that the HiFO-PMD section has negligible influence on the SOPMD statistical distribution. An increase in the amount of FO-PMD on a HiFO-PMD section reduces the output SOP spread to a given minimum, in this study the minimum was reached when the HiFO-PMD ≥ 35 ps. However, the outcome of the output SOP spread depends on the location of the HiFO-PMD section along the fibre link length. It was found that when the HiFO-PMD section introduces SO-PMD, the bit error rate (BER) is much higher compared to when it does not introduce SO-PMD.
- Full Text:
- Date Issued: 2009